DIGITAL MIXER YAMAHA QL5

Mã sản phẩm: QL5

Giá: Vui lòng liên hệ

Nhà sản xuất: YAMAHA

Tình trạng: Còn hàng

Số lượng:

HÀNG CHÍNH HÃNG

BỎ VÀO GIỎ HÀNG

Mô tả
Thông số kỹ thuật
Nhận xét

32 + 2 fader configuration adapts to a wide range of channel layouts. The QL5 is a compact console with large-scale capabilities.

Mix channels: 64 mono, 8 stereo.
Busses: 16 mix, 8 matrix (Input to Matrix supported).
Local I/O: 32 in, 16 out.
Fader configuration: 32 + 2 (Master).
Stainless steel iPad support stays.

Thông số kỹ thuật

Thông số kỹ thuật chung

Tỷ lệ tần suất lấy mẫu	Bên trong	44.1kHz / 48kHz
Tỷ lệ tần suất lấy mẫu	Bên ngoài	44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm)
Độ trễ tín hiệu		Less than 2.5ms, INPUT to OMNI OUT, Fs= 48kHz

General specifications

Fader		100mm motorized, Resolution=1024steps, +10dB to –138dB, –∞dB all faders

Thông số kỹ thuật chung

Tổng độ méo sóng hài		Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, INPUT to OMNI OUT, Input Gain= Min.
Đáp tuyến tần số		+0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUT
Dãy động		112dB typ.: DA Converter / 108dB typ.: INPUT to OMNI OUT, Input Gain = Min.
Mức nhiễu & Ồn	Nhiễu đầu vào tương đương	-128dBu typ., Equivalent Input Noise, Input Gain=Max
Mức nhiễu & Ồn	Nhiễu đầu ra thặng dư	-88dBu, Residual output noise, ST master off
Xuyên âm		-100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min.
Yêu cầu về nguồn điện		100-240V 50/60Hz
Tiêu thụ Điện		200W
Kích thước	Rộng	828mm(32.6in)
	H	272mm(10.7in)
	Sâu	563mm(22.2in)
Trọng lượng tịnh		21.8kg(48.1lb)
Phụ kiện		Owner’s Manual, dust cover, power cord, DVS license sheet

General specifications

Options		Mini-YGDAI cards *2 , Gooseneck Lamp LA1L, Nuendo Live

Thông số kỹ thuật chung

Khác		Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃

Crosstalk@1kHz : A 22kHz, 30dB/Oct filter is used to measure crosstalk.
Total Harmonic Distortion : An 80kHz, 18dB/Oct filter is used to measure total harmonic distortion.
Hum & Noise : An A-Weight filter is used to measure hum &noise.

Analog input characteristics

Input Connectors	GAIN	Input Impedance	Source Impedance	Input level			Connector
Input Connectors	GAIN	Input Impedance	Source Impedance	Sensitivity*¹	Nominal	Max. before clip	Connector
INPUT 1-32 *6	+66dB	7.5 kΩ	50-600 Ω Mics & 600 ΩLines	–82dBu (61.6μV)	–62dBu (0.616mV)	–42dBu (6.16mV)	XLR-3-31 type (Balanced) *2
INPUT 1-32 *6	–6dB	7.5 kΩ	50-600 Ω Mics & 600 ΩLines	–10dBu (245mV)	+10dBu (2.45V)	+30dBu (24.5V)	XLR-3-31 type (Balanced) *2

*1. The sensitivity is the input level required for output at +4dBu (1.23V) or at the defined level when all the faders and level
controllers are set to the maximum value.
*2. XLR-3-31 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*3. 0dBu=0.775 Vms for all specifications.
*4. All the AD converters use 24-bit linear/128-times oversampling.
*5. The INPUT connectors have +48V DC (phantom power) jacks, each of which can be turned on/off individually from the console software.
*6. QL1: INPUT1-16

Analog output characteristics

Output Connectors	Output Impedance	Load Impedance	Maximum Output Level *5	Output Level		Connector
Output Connectors	Output Impedance	Load Impedance	Maximum Output Level *5	Defined Level	Maximum Non-Clip Level	Connector
OMNI OUT 1-16 *7	75 Ω	600 Ω Lines	+24dB (default)	+4dBu (1.23V)	vt+24dBu (12.3V)	XLR-3-32 type (Balanced) *1
OMNI OUT 1-16 *7	75 Ω	600 Ω Lines	+18dB	–2dBu (616mV)	+18dBu (6.16V)	XLR-3-32 type (Balanced) *1
PHONES	15 Ω	8 Ω Phones	-	75mW *6	150mW	Stereo Phone Jack(TRS) (Unbalanced) *2
PHONES	15 Ω	40 Ω Phones	-	65mW *6	150mW	Stereo Phone Jack(TRS) (Unbalanced) *2

*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*2. The PHONES connectors for stereo headphones are balanced jacks (Tip=LEFT, Ring=RIGHT, Sleeve= GND).
*3. 0 dBu=0.775 Vms for all specifications.
*4. All the DA converters use 24-bit linear/128-times oversampling.
*5. The console has an internal switch for toggling the maximum output level.
*6. This is a value measured with the PHONES LEVEL knob set to 10 dB below the maximum position.
*7. QL1: OMNI OUT 1-8

Digital input/output specifications

Connectors	Format	Data length	Level	Audio	Connector
Primary/Secondary	Dante	24bit or 32bit	1000Base-T	64ch Input/64ch Output@48kHz *1	EtherCON Cat5e

*1. QL1: 32ch Input/32ch Output@48kHz

Digital output specifications

Connectors		Format	Data length	Level	Connector
DIGITAL OUT	AES/EBU	AES/EBU Professional Use	24bit	RS422	XLR-3-32 type (Balanced) *1

*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).

I/O SLOT (1-2) specifications

Each I/O Slot accepts a Mini-YGDAI card.
Only Slot 1 has a serial interfac

Control I/O characteristics

Connectors		Format	Level	Connector
MIDI	IN	MIDI	-	DIN Connector 5P
MIDI	OUT	MIDI	-	DIN Connector 5P
WORDCLOCK	IN	-	TTL/75 Ω terminated	BNC Connector
WORDCLOCK	OUT	-	TTL/75 Ω	BNC Connector
GPI (5IN/5OUT)		-	-	D Sub Connector 15P(Female) *1
NETWORK		IEEE802.3	10BASE-T/100Base-TX	RJ-45
LAMP (QL5: x 2, QL1: x 1)		-	0V-12V	XLR-4-31 type *2
USB HOST		USB 2.0	-	USB A Connector (Female)

*1. Input pin: TTL level, w/ internal pull-up (47kΩ) Output pin: Open drain output (Vmax=12V, maximum sink current/pin=-75mA) Power supply pin: Output voltage Vp=5V, Max. output current=300mA
*2. 4 pin=+12V, 3 pin=GND, Lamp nominal power: 5W, Brightness (voltage) can be adjusted from the software.